“This site contains affiliate links for which OEMDTC may be compensated” |
February 20, 2019 NHTSA CAMPAIGN NUMBER: 19V114000
Shock Absorber Forks May Develop Cracks
Loose shock absorbers may impair vehicle steering, increasing the risk of crash.
NHTSA Campaign Number: 19V114
Manufacturer Volkswagen Group of America, Inc.
Components SUSPENSION
Potential Number of Units Affected 32
Summary
Volkswagen Group of America, Inc. (Audi) is recalling certain 2019 Q7, Q8, and S5 Cabriolet vehicles. The front shock absorber forks may develop cracks allowing the shock absorbers to loosen.
Remedy
Audi has notified owners, and dealers will replace the shock absorber forks, free of charge. The recall began March 18, 2019. Owners may contact Audi customer service at 1-800-253-2834. Audi’s number for this recall is 40O4.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Audi has a Recall
Safety Recall
Code: 40O4
Subject | Shock Absorber (Suspension) Fork | ||||||||||||||||||||||||||||||
Release Date | March 06, 2019 | ||||||||||||||||||||||||||||||
Affected Vehicles | U.S.A. & CANADA: Certain 2019 MY Audi Q7 and Audi Q8
Check Campaigns/Actions screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this action. Elsa is the only valid campaign inquiry & verification source.
|
||||||||||||||||||||||||||||||
Problem Description | On certain vehicles, a front shock absorber fork may crack. This may allow the shock absorber to come loose and cause the tire to contact the wheel housing. This could affect steering control.
If the steering system does not work properly, there could be an increased risk of a crash. |
||||||||||||||||||||||||||||||
Corrective Action | Replace the affected shock absorber fork. | ||||||||||||||||||||||||||||||
Parts Information | Due to the small number of affected vehicles, parts will not be allocated prior to launch. Parts will not be blocked and are open to order.
Affected vehicle count: U.S.A.: 22 / Canada: 7
|
||||||||||||||||||||||||||||||
Code Visibility | On or about March 06, 2019, affected vehicles will be listed on the Inventory Vehicle Open Campaign Action report under My Dealership Reports (found on www.accessaudi.com & OMD Web). A list will not be posted for dealers who do not have any affected vehicles.
On or about March 06, 2019, this campaign code will show open on affected vehicles in Elsa. On or about March 06, 2019, affected vehicles will be identified with this campaign code in the VIN Lookup tool at www.audiusa.com and on the NHTSA VIN lookup tool at www.safercar.gov. |
||||||||||||||||||||||||||||||
Owner Notification | Owner notification will take place in March 2019. Owner letter examples are included in this bulletin for your reference. | ||||||||||||||||||||||||||||||
Additional Information | Please alert everyone in your dealership about this action, including Sales, Service, Parts and Accounting personnel. Contact Warranty if you have any questions.
IMPORTANT REMINDER ON VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS New Vehicles in Dealer Inventory: It is a violation of federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied. By law, dealers must correct, prior to delivery for sale or lease, any vehicle that fails to comply with an applicable Federal Motor Vehicle Safety Standard or that contains a defect relating to motor vehicle safety. Pre-Owned Vehicles in Dealer Inventory: Dealers should not deliver any pre-owned vehicles in their inventory which are involved in a safety or compliance recall until the defect has been remedied. Dealers must ensure that every affected inventory vehicle has this campaign completed before delivery to consumers. |
||||||||||||||||||||||||||||||
Claim Entry Instructions
After campaign has been completed, enter claim as soon as possible to help prevent work from being duplicated elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order. If customer refused campaign work:
|
|||||||||||||||||||||||||||||||
Service Number | 40O4 (number 4, number zero, letter O, number 4) | ||||||||||||||||||||||||||||||
Damage Code | 0099 | ||||||||||||||||||||||||||||||
Parts Vendor Code | 002 | ||||||||||||||||||||||||||||||
Claim Type | Sold vehicle: 7 10
Unsold vehicle: 7 90 |
||||||||||||||||||||||||||||||
Causal Indicator | Mark suspension fork as causal part* | ||||||||||||||||||||||||||||||
Vehicle Wash/Loaner | Do not claim wash/loaner under this action | ||||||||||||||||||||||||||||||
Criteria I.D. | 01 | ||||||||||||||||||||||||||||||
Replace left front suspension fork.
|
|||||||||||||||||||||||||||||||
Criteria I.D. | 02 | ||||||||||||||||||||||||||||||
Replace right front suspension fork.
|
Customer Letter Example (USA)
<MONTH YEAR>
<CUSTOMER NAME>
<CUSTOMER ADDRESS>
<CUSTOMER CITY STATE ZIPCODE>
This notice applies to your vehicle: <VIN>
NHTSA: 19V114
Subject: | Safety Recall 40O4 – Shock Absorber Fork Certain 2019 Model Year Audi Q7 and Audi Q8 Vehicles |
Dear Audi Owner,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Audi has decided that a defect, which relates to motor vehicle safety, exists in certain 2019 model year Audi A7 and Audi Q8 vehicles. Our records show that you are the owner of a vehicle affected by this action.
What is the issue? | On certain vehicles, a front shock absorber fork may crack. This may allow the shock absorber to come loose and cause the tire to contact the wheel housing. This could affect steering control. If the steering system does not work properly, there could be an increased risk of a crash. |
What will we do? | To correct this defect, your authorized Audi dealer will replace the affected shock absorber fork. This work will take about an hour to complete and will be performed for you free of charge. Please keep in mind that your dealer may need additional time for the preparation of the repair, as well as to accommodate their daily workshop schedule. |
What should you do? | Please contact your authorized Audi dealer without delay to schedule this recall repair. For your convenience, you can also visit www.audiusa.com and click on the “Find a Dealer” link to locate a dealer near you and schedule this service. |
Lease vehicles and address changes | If you are the lessor and registered owner of the vehicle identified in this action, the law requires you to forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt. If you have changed your address or sold the vehicle, please fill out the enclosed prepaid Owner Reply card and mail it to us so we can update our records. |
Can we assist you further? | If your authorized Audi dealer fails or is unable to complete this work free of charge within a reasonable time, please contact Audi Customer Experience at 1-800-253-2834 or via our “Contact Us” page at www.audiusa.com. |
Checking your vehicle To check your vehicle’s eligibility for repair under this or any other recall/service campaign, for open Recalls and please visit the Recall/Service Campaign Lookup tool at www.audiusa.com and enter your Service Campaigns Vehicle Identification Number (VIN).
If you still cannot obtain satisfaction, you may file a complaint with: The Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov.
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your safety and continued satisfaction with your vehicle.
Sincerely,
Audi Customer Protection
Customer Letter Example (CANADA)
<MONTH YEAR>
<CUSTOMER NAME>
<CUSTOMER ADDRESS>
<CUSTOMER CITY STATE ZIPCODE>
This notice applies to your vehicle: <VIN>
Subject: | Safety Recall 40O4 – Shock Absorber Fork Certain 2019 Model Year Audi Q7 and Audi Q8 Vehicles |
Dear Audi Owner,
This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act. Audi has decided that a defect, which relates to motor vehicle safety, exists in certain 2019 model year Audi Q7 and Audi Q8 vehicles. Our records show that you are the owner of a vehicle affected by this action.
What is the issue? | On certain vehicles, a front shock absorber fork may crack. This may allow the shock absorber to come loose and cause the tire to contact the wheel housing. This could affect steering control. If the steering system does not work properly, there could be an increased risk of a crash. |
What will we do? | To correct this defect, your authorized Audi dealer will replace the affected shock absorber fork. This work will take about an hour to complete and will be performed for you free of charge. Please keep in mind that your dealer may need additional time for the preparation of the repair, as well as to accommodate their daily workshop schedule. |
What should you do? | Please contact your authorized Audi dealer without delay to schedule this recall repair. |
Lease vehicles and address changes | If you are the lessor and registered owner of the vehicle identified in this action, the law requires you to forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt. If you have changed your address or sold the vehicle, please fill out the enclosed prepaid Owner Reply card and mail it to us so we can update our records. |
Can we assist you further? | If your authorized Audi dealer fails or is unable to complete this work free of charge within a reasonable time, please contact Audi Customer Relations Monday through Friday from 8AM to 8PM EST at 1-800-822-2834 or via our “Contact Audi Canada” page at www.audi.ca. |
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your safety and continued satisfaction with your vehicle.
Sincerely,
Audi Customer Protection
SEOCONTENT-START
Campaign Work Procedure 40O4 Safety Recall
Repair Overview
NOTE
• These repair instructions may differ from the labor operations and labor times listed in ELSA.
• Damages resulting from improper repair or failure to follow these work instructions are the dealer’s responsibility and are not eligible for reimbursement under this action.
• This procedure must be read in its entirety prior to performing the repair.
• Due to variations in vehicle equipment and options, the steps/illustrations in this work procedure may not identically match all affected vehicles.
• Diagnosis and repair of pre-existing conditions in the vehicle are not covered under this action.
• When working during extreme temperatures, it is recommended that the vehicle be allowed to acclimate inside the shop to avoid temperature-related component damage/breakage.
• Replace front suspension fork
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 7 of 17
Required Parts
Criteria
Quantity
Part Number
Part Description
01
1
4M0.413.037.H
Suspension Fork (left)
02
1
4M0.413.038.H
Suspension Fork (right)
ALL
1
N 102.722.02
Bolt, hex head (M12x1.5×95)
1
N 101.064.02
Shouldered hex nut, self-locking (M12x1.5)
1
WHT.007.061
12 point socket head screw (M10x85)
2
N 102.861.10
Shouldered hex nut, self-locking (M10)
1
N 107.847.02
Hexagon flange screw (M12x1.5×85)
1
WHT.001.987
Hex nut, self-locking with washer (M12x1.5)
1
WHT.006.917
12 point socket head screw (M10x62)
NOTE
The specified part numbers reflect the status at the start of this recall. Interim updates made in ETKA can cause a listed part number to become unavailable. In this case, the new part number specified in ETKA should be used.
Required Tools
Spreader Tool
-3424-
(or equivalent)
Torque Wrench 1331 5-50Nm
-VAG1331-
(or equivalent)
Torque Wrench 1332 40-200Nm
-VAG1332-
(or equivalent)
Engine and Gearbox Jack
-VAS6931-
(or equivalent)
Engine/Gearbox Jack Adapter – Wheel Hub Support
-T10149-
(or equivalent)
Tensioning Strap
T10038
(or equivalent)
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 8 of 17
Repair Instruction
Section A – Check for Previous Repair
• Enter the VIN in Elsa and proceed to the “Campaign/Action” screen.
TIP
On the date of repair, print this screen and keep a copy with the repair order.
• Confirm the Campaign/Action is open <arrow 1>. If the status is closed, no further work is required.
• Note the Applicable Criteria ID <arrow 2> for use in determining the correct work to be done and corresponding parts associated.
Proceed to Section B
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 9 of 17
Section B – Replace Front Suspension Fork
Measuring and recording curb weight position:
• Before starting the procedure, determine the measurement <a>, using a tape measure, from the center of the wheel to the lower edge of the fender/wheel housing.
• Record the measurement on the repair order.
Raising and securing vehicle to hoist:
WARNING
When suspension is lifted in curb weight position, the vehicle must be secured on the hoist to prevent it from tipping off the hoist.
• Raise the vehicle on a hoist and remove the front wheels.
• Lightly secure both sides of the vehicle to the hoist lifting arms <arrow> using -T10038- on the upper rear control arm mounts <arrow A>.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 10 of 17
• Secure both sides of the vehicle to the hoist lifting arms <arrow B> through the strikers on the rear doors <arrow A> using -T10038-.
Pre-load suspension prior to fastener removal:
NOTE
Risk of destroying the wheel bearing when installing the wheel bolt.
Install a washer <1> on the wheel bolt <2> so that the wheel bolt does not press against the wheel bearing.
• Install the -T10149- with a wheel bolt <2> and inserted washer <1> on the wheel hub.
• Slightly lift the wheel bearing housing using the -T10149- with the -VAS6931-. This allows the threaded connections to easily separate.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 11 of 17
Removing front suspension fork:
• Remove the coupling rod <2> upper and lower nuts and bolts and remove the coupling rod.
• Loosen and remove the fasteners <1 and 2> for the shock absorber fork.
• Push the bracket <3> with the brake hose to the side.
• Lower and remove the engine and gearbox jack -VAS6931- from the wheel hub.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 12 of 17
• Insert the -3424- into the slot in the suspension fork <arrow> and separate the suspension fork from the shock absorber tube.
NOTE
There is a risk of damaging the ball joint if force is used. Never press the joints in the control arm past the maximum articulation.
• Remove the suspension fork downward from the shock absorber tube.
• Carefully press the wheel bearing housing downward and remove the suspension fork.
Installing new suspension fork:
• Install new suspension fork, making sure the T-pin <1> of the shock absorber tube engages in the groove <arrow> on the suspension fork.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 13 of 17
• Install new nuts and bolts in the positions shown, but do not tighten.
Image
Part Number
Part Description
4M0.413.037.H
-OR-
4M0.413.038.H
Suspension Fork
-AND-
<1>
N 102.722.02
Bolt, hex head (M12x1.5×95)
<2>
N 101.064.02
Shouldered hex nut, self-locking (M12x1.5)
<3>
WHT.007.061
12 point socket head screw (M10x85)
<4>
N 102.861.10
Shouldered hex nut, self-locking (M10)
<5>
N 107.847.02
Hexagon flange screw (M12x1.5×85)
<6>
WHT.001.987
Hex nut, self-locking with washer (M12x1.5)
<7>
WHT.006.917
12 point socket head screw (M10x62)
<8>
N 102.861.10
Shouldered hex nut, self-locking (M10)
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 14 of 17
Setting curb weight position:
NOTE
Risk of destroying the wheel bearing when installing the wheel bolt.
Install a washer <1> on the wheel bolt <2> so that the wheel bolt does not press against the wheel bearing.
• Install the -T10149- with a wheel bolt <2> and inserted washer <1> on the wheel hub.
• Lift the wheel bearing housing using the -T10149- with the -VAS6931- until the previously recorded curb weight position is achieved.
WARNING
When suspension is lifted in curb weight position, the vehicle must be secured on the hoist to prevent it from tipping off the hoist.
CAUTION
• All bolts on suspension components with bonded rubber bushings must always be tightened in curb weight position (unloaded condition).
• Bonded rubber bushings have a limited range of rotation.
• Axle components with bonded rubber bushings must be brought into the position they will be in when driving before they are tightened (curb weight position). Otherwise, the bonded rubber bushing will have tension, which will reduce the service life.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 15 of 17
Tightening suspension fasteners:
• With the suspension in curb weight position, counter-hold the upper bolt for the upper suspension fork connection and tighten the nut <2> to 40 Nm + 180°.
• Counter-hold the lower bolt for the lower suspension fork connection and tighten the nut <1> to 90 Nm + 90°.
• With the suspension in curb weight position, counter-hold the upper and lower bolts for the anti-sway bar coupling rod <2> and tighten the nuts to 40 Nm + 90°.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 16 of 17
• Lower the engine and gearbox jack -VAS6931- and remove the -T10149-.
• Remove the tensioning straps -T10038- from the front upper control arms and rear door strikers.
• Reinstall the front wheels and torque the bolts to 160 Nm.
All work complete, Proceed to Section C
Section C – Campaign Completion Stamp
Item#: AUD4927ENG
-OR-
Item # AUD4927FRE
• Once the campaign has been completed, the technician should stamp the repair order.
• Stamps are available for ordering through the Compliance Label Ordering Portal.
• Proceed to Section D
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2019 Audi of America, Inc. and Audi Canada. All Rights Reserved.
March 2019 40O4 Page 17 of 17
Section D – Parts Return/Disposal
Properly store (retain), destroy or dispose of removed parts in accordance with all state/province and local requirements, unless otherwise indicated and/or requested through the Warranty Parts Portal (WPP) for U.S. and the Part Destruction and Core Disposition Report for Canada.
SEOCONTENT-END
3 Affected Products
Vehicles
MAKE | MODEL | YEAR |
AUDI | Q7 | 2019 |
AUDI | Q8 | 2019 |
AUDI | S5 CABRIOLET | 2019 |
12 Associated Documents
ISSUED Owner Notification Letter(Part 577)
RCONL-19V114-7826.pdf 42.555KB
Recall 573 Report-Amendment 1
RCLRPT-19V114-8051.PDF 216.085KB
Recall 573 Report-Amendment 2
RCLRPT-19V114-8870.PDF 217.612KB
Manufacturer Notices(to Dealers,etc) – March 05, 2019 Repair Available – Safety Recall 40O4 / Shock Absorber (Suspension) Fork
Defect Notice 573 Report
RCLRPT-19V114-9148.PDF 215.869KB
Remedy Instructions and TSB
RCRIT-19V114-2837.pdf 798.736KB
Recall Acknowledgement
RCAK-19V114-1454.pdf 244.973KB
ISSUED Owner Notification Letter(Part 577) – PRI
RCONL-19V114-5675.pdf 53.756KB
Recall Quarterly Report #1, 2019-1
RCLQRT-19V114-8176.PDF 211.15KB
Recall Quarterly Report #2, 2019-2
RCLQRT-19V114-1826.PDF 211.253KB
Recall 573 Report-Amendment 3
RCLRPT-19V114-6393.PDF 218.241KB
Recall Quarterly Report #3, 2019-3
RCLQRT-19V114-0398.PDF 211.333KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V114&docType=RCL
- DEEP & EFFECTIVE CLEANING: Foaming gel sticks for deep cleaning
- SPECIALIZED FOR BLACK WHEELS: Formulated for all black wheel finishes
- POWERFUL & SAFE: Maximum cleaning yet gentle on wheels
- CLINGING ACTION: Formula dwells on the surface for more effective cleaning
- VERSATILE USE: Safely and effectively cleans glossy, matte, satin, and black chrome wheels
- TOUGH ON GRIME - Signature Series is a strong citrus-based wheel cleaner that is tough on brake dust and filth, but gentle and safe for most wheel finishes and materials.
- NATURAL CITRUS CLEANING POWER - Signature Series Wheel Cleaner is blended with natural citrus extracts for powerful cleaning of dirt, grime, and brake dust. Brake dust contains corrosive iron and carbon deposits that can destroy wheels.
- SUPER CONCENTRATED - Adding Signature Series to normal wheel cleanings reduces buildup and corrosion and protects a pristine showroom shine; Clean rubber tire sidewalls to ensure tire shine dressings last longer and look better!
- WE MAKE LOOKING GOOD EASY - Spray the cleaner directly onto alloy wheels, plastic wheel covers, brake parts, suspension parts, plastic fender liners, or undercarriage parts to break down caustic grime and filth.
- THE GO TO BRAND IN CAR CARE - Beginners and professionals alike choose Chemical Guys, not only for the finest car care products, but the world class customer support and vast detailing knowledge Chemical Guys is more than a brand it's a lifestyle with a worldwide following
- ✅ ELIMINATES DIRT, BROWNING, AND BRAKE DUST - Which part of your car takes the biggest beating? Your wheels & Tires! Between the heat, elements, and constant brake contaminants your wheels are almost immediately dirty. Adam’s Wheel & Tire Cleaner is a specifically formulated chemical designed to target heavy brake dust and restore your tires back to factory color.
- ✅ SAFE ON MANY FINISHES - Safe on clear-coated, powder-coated, chrome, alloy, and painted wheels. Most wheel cleaners can be harmful to your wheel finish and dissolve more than what you wanted to clean off! Adam’s Polishes Wheel & Tire Cleaner gets to work fast and dissolves stubborn metallic contamination.
- ✅ GET RID OF BROWN TIRES - If you’re happy with brown, old and decrepit tires, look away! If you’re wanting to thoroughly clean your vehicle’s shoes and make them look like new again, then look no further! Adam's Wheel & Tire Cleaner contains a blend of alkaline-concentrated solvents and surfactants to create a high sudsing formula and removes silicones, greases, wax build-up, polymers, and any previously applied dressings to leave your tires and wheels looking new.
- ✅ EXTEND YOUR TIRE DRESSINGS LIFE - Adam’s Wheel & Tire Cleaner is a detailing essential for any user, from rookie to professional. When investing in premium protective options, high foaming soaps, and ultra-premium microfiber towels, your vehicle's shoes need to be kept clean to not take away from the rest of the vehicle. If you choose not to clean your tires, your tire dressings have no chance of sticking around. Clean your tires before with Wheel & Tire Cleaner to maximize your tire shine.
- ✅ 110% SATISFACTION GUARANTEE - At Adam’s, we strive to bring the BEST waxes, sealants, ceramic coatings, microfiber towels, wash mitts, garage tools, accessories, detailing kits, sponges, applicators and other high-quality car cleaning products to our customers. If you don’t agree & are not satisfied, let us know and we’ll do everything we can to make it right!
- This acid-free wheel, tire, and brake cleaner is safe for all wheel types and finishes, including, steel, aluminum, chrome, paint, powder coat, and more. This cleaner is harsh on removing brake dust, iron, and road fallout, but easy on your rims.
- Restore your tires and wheels to a factory-fresh color. Just spray it on, let it clean, and agitate with a soft bristle brush on the face, barrel, tire, and brake parts to break up stubborn contaminants. Just spray with water afterward and clean with a microfiber towel.
- Can be used straight from the bottle or diluted in a foam sprayer. This product can be diluted in any foam sprayer to create a generous foram that easily lifts first, brake dust, and road contaminants from the wheel and tire.
- Leaves a protective coating that helps repel any future tarnishing, staging, or grime buildup. In addition, you can easily and safely apply wheel and tire sealants to extend the life of your clean and shiny wheels.
- FOAMING CLEANER FOR YOUR WHEELS & RIMS - Oxygen-infused cleaners and slick lubricants in Sprayable Diablo Wheel Cleaner form a foaming lather to lubricate surfaces and gently guide dirt and grime off of your wheels for the gentlest and most thorough clean available.
- BEGINNER AND PROFESSIONAL DETAILER FRIENDLY – Chemical Guys makes products for beginners and experts alike. Chemical Guys products are professional grade to get the best results and are also simple enough for even a beginner to achieve immediate results.
- Chemical Guys Sticky Citrus Wheel Cleaner Gel is the all-natural solution that cleans and degreases nasty wheels fast. Customers and clients requested a product that would remove stubborn brake dust with minimal scrubbing countless times.
- PRESERVE YOUR SENSITIVE WHEEL & RIM FINISHES - Brake dust and road filth are not just ugly, they will destroy your wheels if left unchecked. Diablo wheel gel removes abrasive and corrosive particulates before they can damage your sensitive wheel finishes.
- SAFELY CLEAN ANY TYPE OF WHEEL WITHOUT SCRATCHING - Unlike other wheel cleaners, Diablo Wheel Gel uses no caustic acids or heavy alkaline compounds and won’t harm your shiny wheel finishes while your clean. The advanced foaming formula safely lifts dirt and grime to help prevent scratches and swirls.
- Safely dissolves grease road grime and brake dust on contact
- Reveals your wheel's brilliant shine
- Safe for all wheels
- Fit type: Universal Fit
- Safe On All Factory Installed Wheels: Acid-Free, Ph Balanced Formula Won'T Damage Wheels, Safe On Various Wheel Finishes Including: Chrome, Aluminum, Steel, Clear Coated, Pvd, Painted, Plastic Wheel Covers, And Magnesium
- Watch It Work: The Color Changing Formula Activates When It Comes In Contact With The Ferrous Metals (Iron) From Brake Dust Or Other Dirt And Grime. Full Effect Sprays On Fluorescent Yellow, Then Turns Deep Red Or Purple As It Dissolves Brake Dust
- Advanced And Effective Chemistry: Full Effect, Non Acid Wheel Cleaner Attaches And Emulsifies Stubborn Baked On Brake Dust. Simply Spray On, Let It Dwell, Watch For Color Change, Agitate If Necessary, And Rinse With Water. *For Best Results Rinse Using High Pressure Water
- Full Effect Is Great For Both The Diy (Do-It-Yourself) And The Professional. Effortlessly Achieve Shining Wheels That Will Make Your Vehicle Look Like It Just Rolled Off The Showroom Floor
- ✅ WHY CHOOSE ADAM’S WHEEL CLEANER? - Which part of your car takes the biggest beating? Your wheels! Due to constant heat, elements, & constant brake contaminants, your wheels are almost always dirty. Adam’s wheel cleaning chemical formula was specifically formulated to target & eliminate heavy brake dust and leave your wheels spotless!
- ✅ ADVANCED CHEMICAL TECHNOLOGY - Our Wheel Cleaner was made to compliment your arsenal of car cleaning supplies. Every basic auto detailing kit needs an effective wheel cleaner, car wash soap, tire shine, & some sort of paint protection. This state of the art wheel cleaner is a simple spray & agitate formula. This chemical is certain to be the best wheel cleaner and brake dust remover that you have ever used.
- ✅ CAR CLEANING MADE EASY - Most wheel cleaners can be harmful to your wheel finish and dissolve more than what you wanted to clean off! Adam’s Polishes Wheel Cleaner gets to work fast and dissolves stubborn metallic contamination. Simply spray our Wheel Cleaner & watch as the brake dust bleeds bright purple & falls off! This acid-free and pH neutral formula penetrates dirt and grime at the source and makes your wheel cleaning time significantly shorter!
- ✅ IS IT SAFE FOR MY WHEEL FINISH? - Adam’s Wheel Cleaner is safe on almost all wheel finishes, which includes clear-coated, powder-coated, chrome, alloy, and painted wheels. However, it may not be safe on anodized raw aluminum, polished aluminum wheels, and aftermarket bare metallic wheels. If you are not sure reach out to us by sending us a message or simply try our Eco Wheel Cleaner or Wheel & Tire Cleaner!
- ✅ 110% SATISFACTION GUARANTEE & USA MADE - At Adam’s, we strive to bring the BEST car cleaning supplies, auto detailing kits, washing accessories, microfiber towels, waxes, sealants, ceramic coatings, mops, brushes, mitts, sponges, garage tools, applicators & other high-quality car cleaning products to the car care industry. If you are not satisfied, let us know & we’ll do everything we can to make it right!
- Effective and easy cleaning on wheels and tires
- Quickly removes Brake dust, road grime, light grease and dirt
- Spray on, lightly Agitate, Hose off
- READY TO USE FORMULA: Pre-diluted, no mixing required
- Fast reacting foaming formula, quickly dissolves dirt, grime, heavy brake dust and browning. Leaves wheels and tires perfectly prepped for tire dressing or coatings.
- Contains a corrosion repellant polymer that reduces contaminant build-up, keeping wheels and tires cleaner longer, and makes future cleaning faster and easier.
- Application is easy. Apply liberally one wheel at a time, allowing formula to sit for up to one minute, agitate with a soft wheel cleaner brush or cloth and rinse thoroughly. Repeat if necessary.
- For amazing shine, gloss, and deep black tires, treat the surface with our Hybrid Solutions Graphene Acrylic Tire Shine Coating.
- Not meant for use on non-factory painted wheels, non-coated aluminum, or motorcycle wheels. If unsure, test on an inconspicuous area.
Last update on 2024-02-29 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.