December 9, 2020 NHTSA CAMPAIGN NUMBER: 20V760000
Terminal Cover Can Compromise 12-Volt Power Supply
In the event of a rear crash, the incorrect cover can cause the 12-volt power supply to be compromised, preventing the vehicle doors from being opened from the outside, or the hazard warning lights from functioning, increasing risk of injury.
NHTSA Campaign Number: 20V760
Manufacturer Volkswagen Group of America, Inc.
Components ELECTRICAL SYSTEM
Potential Number of Units Affected 2,355
Summary
Volkswagen Group of America, Inc. (Audi) is recalling certain 2018-2019 Audi RS5 Coupe vehicles. An incorrect positive battery terminal cover was installed.
Remedy
Audi will notify owners, and dealers will replace the positive terminal cover, free of charge. The recall began January 19, 2021. Owners may contact Audi customer service at 1-800-253-2834. Audi’s number for this recall is 27i6.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Audi has a Recall
Problem Description
The affected vehicles were erroneously equipped with a plus (positive) terminal cover that might be less capable of assuring 12 V-power supply in a rear crash according to FMVSS and CMVSS 301 (Fuel system integrity) at 80 km/h (approximately 50 mph). In case of a rear crash (according to FMVSS/CMVSS 301 at 80 km/h (approximately 50 mph)) it may be possible for the 12-volt power supply of the vehicle to become compromised.
While there is no noncompliance with FMVSS/CMVSS 301, this could result in not being possible to open the vehicle doors from the outside, or the hazard warning lights may not function due to a compromised electric power supply. This may lead to an increased risk of injury to vehicle occupants in a rear crash if the power supply is affected.
Corrective Action
Replace the plus (positive) terminal cover.
Code Visibility
On or about January 12, 2021, the campaign code will be applied to affected vehicles.
Owner Notification
Owner notification will take place in January 2021. Owner letter examples are included in this bulletin for your reference.
Repair Overview
Replace positive battery terminal cover.
Repair Procedure
- Install new positive battery terminal cover <arrow>.
- Ensure the cover is clipped in and secured.
SEOCONTENT-START
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 1 of 9
Safety Recall
Code: 27i6
Subject
Terminal Cover
Release Date
January 12, 2021
Affected Vehicles
Country
Beginning Model Year
Ending Model Year
Vehicle
Vehicle Count
USA
2018
2019
RS5 COUPE
2,355
CAN
2018
2019
RS5 COUPE
447
Check Campaigns/Actions screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this action. Elsa is the only valid campaign inquiry & verification source.
Campaign status must show “open.”
If Elsa shows other open action(s), inform your customer so that the work can also be completed at the same time the vehicle is in the workshop for this campaign.
Problem Description
The affected vehicles were erroneously equipped with a plus (positive) terminal cover that might be less capable of assuring 12 V-power supply in a rear crash according to FMVSS and CMVSS 301 (Fuel system integrity) at 80 km/h (approximately 50 mph). In case of a rear crash (according to FMVSS/CMVSS 301 at 80 km/h (approximately 50 mph)) it may be possible for the 12-volt power supply of the vehicle to become compromised.
While there is no noncompliance with FMVSS/CMVSS 301, this could result in not being possible to open the vehicle doors from the outside, or the hazard warning lights may not function due to a compromised electric power supply. This may lead to an increased risk of injury to vehicle occupants in a rear crash if the power supply is affected.
Corrective Action
Replace the plus (positive) terminal cover.
Code Visibility
On or about January 12, 2021, the campaign code will be applied to affected vehicles.
Owner Notification
Owner notification will take place in January 2021. Owner letter examples are included in this bulletin for your reference.
Additional Information
Please alert everyone in your dealership about this action, including Sales, Service, Parts and Accounting personnel. Contact Warranty if you have any questions.
IMPORTANT REMINDER ON VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS
New Vehicles in Dealer Inventory: It is a violation of federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied. By law, dealers must correct, prior to delivery for sale or lease, any vehicle that fails to comply with an applicable Federal Motor Vehicle Safety Standard or that contains a defect relating to motor vehicle safety.
Pre-Owned Vehicles in Dealer Inventory: Dealers should not deliver any pre-owned vehicles in their inventory which are involved in a safety or compliance recall until the defect has been remedied.
Dealers must ensure that every affected inventory vehicle has this campaign completed before delivery to consumers.
The information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These procedures
are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To determine whether
this information applies, contact an authorized Audi dealer. 2021 Audi Group of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 2 of 9
Parts Information
Parts Control Type:
VIN to Order
If parts are needed to support a vehicle repair:
• US Dealers – use AVA
• CAN Dealers – contact the Parts Specialists via phone (800-767-6552), email (VWoAPartsSpecialists@vw.com), or chat/text with the VIN to order
Initial Allocation:
YES
Dealers will be sent an initial allocation prior to customer notification. If no initial allocation was received, please reference the Repair Projection Tool (below) to view your potential VIN population.
Repair Projection Tool:
(right click to open)
Criteria
Quantity
Part Number
P.O.C. Part Description
Ordering Method
01
1
8W7-915-429
Cap
VIN to Order
NOTE
The specified part numbers reflect the status at the start of this action. Interim updates made in ETKA can cause a listed part number to become unavailable. In this case, the new part number specified in ETKA should be used.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 3 of 9
Claim Entry Instructions
The labor times listed here may differ from the labor operations and labor times listed in ELSA.
After campaign has been completed, enter claim as soon as possible to help prevent work from being duplicated elsewhere. Attach the Elsa screen print showing action open on the day of repair to the repair order.
If customer refused campaign work:
U.S. dealers: Submit the request through Audi Warranty Online under the Campaigns/Update option.
Canada dealers: Upload the repair order [signed by customer] to Audi WIN/Operations/Campaign Closure.
Service Number
27i6
Damage Code
0099
Parts Vendor Code
002
Claim Type
Sold vehicle: 7 10
Unsold vehicle: 7 90
Causal Indicator
Mark cap* as causal part
Vehicle Wash/Loaner
Do not claim wash/loaner under this action
Criteria I.D.
01
LABOR
Labor Op
Time Units
Description
2706 49 99
30
Replace positive battery terminal cover
PARTS
Quantity
Part Number
Description
1.00
8W7915429
Cap*
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 4 of 9
Customer Letter Example (USA)
<MONTH YEAR>
<CUSTOMER NAME>
<CUSTOMER ADDRESS>
<CUSTOMER CITY STATE ZIPCODE>
This notice applies to your vehicle: <MODEL YEAR> <BRAND> <CARLINE>, <VIN>
NHTSA: 20V760
Subject: Safety Recall 27i6 – Terminal Cover
Dear Audi Owner,
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Audi has decided that a defect, which relates to motor vehicle safety, exists in certain 2018-2019 model year Audi RS5 Coupe vehicles. Our records show that you are the owner of a vehicle affected by this action.
What is the issue?
The affected vehicles were erroneously equipped with a plus (positive) terminal cover that might be less capable of assuring 12 V-power supply in a rear crash at approximately 50 mph. In case of a rear crash, it may be possible for the 12-volt power supply of the vehicle to become compromised.
This could result in not being possible to open the vehicle doors from the outside, or the hazard warning lights may not function due to a compromised electric power supply. This may lead to an increased risk of injury to vehicle occupants in a rear crash.
What will we do?
To correct this defect, your authorized Audi dealer will replace the plus (positive) terminal cover. This work will take about half an hour to complete and will be performed for you free of charge. Please keep in mind that your dealer may need additional time for the preparation of the repair, as well as to accommodate their daily workshop schedule.
What should you do?
Please contact your authorized Audi dealer without delay to schedule this recall repair. For your convenience, you can also visit www.audiusa.com and click on the “Find a Dealer” link to locate a dealer near you and schedule this service.
Lease vehicles and address changes
If you are the lessor and registered owner of the vehicle identified in this action, the law requires you to forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt. If you have changed your address or sold the vehicle, please fill out the enclosed prepaid Owner Reply card and mail it to us so we can update our records.
Can we assist you further?
If your authorized Audi dealer fails or is unable to complete this work free of charge within a reasonable time, please contact Audi Customer Experience at 1-800-253-2834 or via our “Contact Us” page at www.audiusa.com.
Checking your vehicle for open Recalls and Service Campaigns
To check your vehicle’s eligibility for repair under this or any other recall/service campaign, please visit the Recall/Service Campaign Lookup tool at www.audiusa.com and enter your Vehicle Identification Number (VIN).
If you still cannot obtain satisfaction, you may file a complaint with: The Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safercar.gov.
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your safety and continued satisfaction with your vehicle.
Sincerely,
Audi Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 5 of 9
Customer Letter Example (Canada)
<MONTH YEAR>
<CUSTOMER NAME>
<CUSTOMER ADDRESS>
<CUSTOMER CITY STATE ZIPCODE>
This notice applies to your vehicle: <MODEL YEAR> <BRAND> <CARLINE>, <VIN>
Transport Canada Recall: 2020-604
Subject: Safety Recall 27i6 – Terminal Cover
Dear Audi Owner,
This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act. This is to inform you that your vehicle may contain a defect that could affect the safety of a person. Our records show that you are the owner of a vehicle affected by this action.
What is the issue?
The affected vehicles were erroneously equipped with a plus (positive) terminal cover that might be less capable of assuring 12 V-power supply in a rear crash according to Canadian Motor Vehicle Safety Standard (CMVSS) 301 Fuel System Integrity at 80 km/h. In case of a rear crash (according to CMVSS 301 at 80 km/h) it may be possible for the 12-volt power supply of the vehicle to become compromised.
While there is no noncompliance with CMVSS 301, this could result in not being possible to open the vehicle doors from the outside, or the hazard warning lights may not function due to a compromised electric power supply. This may lead to an increased risk of injury to vehicle occupants in a rear crash if the power supply is affected.
What will we do?
To correct this defect, your authorized Audi dealer will replace the plus (positive) terminal cover. This work will take about half an hour to complete and will be performed for you free of charge. Please keep in mind that your dealer may need additional time for the preparation of the repair, as well as to accommodate their daily workshop schedule.
What should you do?
Please contact your authorized Audi dealer without delay to schedule this recall repair.
Lease vehicles and address changes
If you are the lessor and registered owner of the vehicle identified in this letter, you shall forward this letter (and any subsequent notice, if applicable) to the lessee within ten (10) days of receipt. If you have changed your address or sold the vehicle identified in this letter, please fill out the enclosed prepaid Owner Reply Card and mail it to us so we can update our records.
Can we assist you further?
If your authorized Audi dealer fails or is unable to complete this work free of charge within a reasonable time, please contact Audi Customer Relations Monday through Friday from 8AM to 8PM EST at 1-800-822-2834 or via our “Contact Audi Canada” page at www.audi.ca.
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your safety and continued satisfaction with your vehicle.
Sincerely,
Audi Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 6 of 9
Repair Overview
• Replace positive battery terminal cover.
NOTE
• These repair instructions may differ from the labor operations and labor times listed in ELSA.
• Damages resulting from improper repair or failure to follow these work instructions are the dealer’s responsibility and are not eligible for reimbursement under this action.
• This procedure must be read in its entirety prior to performing the repair.
• Due to variations in vehicle equipment and options, the steps/illustrations in this work procedure may not identically match all affected vehicles.
• Diagnosis and repair of pre-existing conditions in the vehicle are not covered under this action.
• When working during extreme temperatures, it is recommended that the vehicle be allowed to acclimate inside the shop to avoid temperature-related component damage/breakage.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 7 of 9
Repair Instruction
Section A – Check for Previous Repair
• Enter the VIN in Elsa and proceed to the “Campaign/Action” screen.
TIP
On the date of repair, print this screen and keep a copy with the repair order.
• Confirm the Campaign/Action is open <arrow 1>. If the status is closed, no further work is required.
• Note the Applicable Criteria ID <arrow 2> for use in determining the correct work to be done and corresponding parts associated.
CRITICAL REPAIR STEP
STOP!
If multiple software update Campaign/Actions are open, they must be performed in order of the Start date <arrow 3>. The oldest should be performed first.
• All Safety Recalls must be completed prior to completing this campaign.
• Proceed to Section B.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 8 of 9
Section B – Repair Procedure
• Access the battery.
• Remove positive battery terminal cover <1>.
• Install new positive battery terminal cover <arrow>.
• Ensure the cover is clipped in and secured.
Proceed to Section C
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Audi dealer. 2021 Audi of America, Inc. and Audi Canada. All Rights Reserved.
January 2021 27i6 Page 9 of 9
Section C – Campaign Completion Stamp
Item#: AUD4927ENG
-OR-
Item # AUD4927FRE
• Once the campaign has been completed, the technician should stamp the repair order.
• Stamps are available for ordering through the Compliance Label Ordering Portal.
Proceed to Section D
Section D – Parts Return/Disposal
Properly store (retain), destroy or dispose of removed parts in accordance with all state/province and local requirements, unless otherwise indicated and/or requested through the Warranty Parts Portal (WPP) for U.S. and the Part Destruction and Core Disposition Report for Canada.
***************************************************************************************************************
AUDI DEALER COMMUNICATION
Ensure all dealership personnel are aware of this notice so they are able to address customer questions. Contact Warranty if you require
additional assistance. Direct press inquiries to Audi Public Relations.
Audi Customer Protection 27i6_DLR_ADV
Advance Notice – Safety Recall 27i6 / Terminal Cover
This notice is for: Dealer Principal
General Manager
Sales Managers
Service Manager
Parts Manager
Service Advisor
Warranty Administrator
Technicians
Date: December 17, 2020
Issue: The affected vehicles were erroneously equipped with a plus (positive) terminal cover
that might be less capable of assuring 12 V-power supply in a rear crash according to
FMVSS and CMVSS 301 (Fuel system integrity) at 80 km/h (approximately 50 mph). In
case of a rear crash (according to FMVSS/CMVSS 301 at 80 km/h (approximately 50
mph)) it may be possible for the 12-volt power supply of the vehicle to become
compromised.
While there is no noncompliance with FMVSS/CMVSS 301, this could result in not being
possible to open the vehicle doors from the outside, or the hazard warning lights may not
function due to a compromised electric power supply. This may lead to an increased risk
of injury to vehicle occupants in a rear crash if the power supply is affected.
Repair: REPAIR NOT YET AVAILABLE – December 18, 2020
Check daily campaign open inventory report or OMD for affected vehicles in
inventory
Affected Vehicles Country Beginning
Model Year
Ending
Model Year Vehicle Vehicle
Count
USA 2018 2019 RS5 COUPE 2,355
CAN 2018 2019 RS5 COUPE 447
*Counts reflect overall population; some vehicles may have already been repaired. Check Campaigns/Actions
screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this action. Elsa is the only valid
campaign inquiry & verification source.
Notes:
IMPORTANT REMINDER: VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS
New Vehicles in Dealer Inventory: It is a violation of federal law for a dealer to deliver a new
motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by
this notification under a sale or lease until the defect or noncompliance is remedied. By law,
dealers must correct, prior to delivery for sale or lease, any vehicle that fails to comply with an
applicable Federal Motor Vehicle Safety Standard or that contains a defect relating to motor
vehicle safety.
Pre-Owned Vehicles in Dealer Inventory: Dealers should not deliver any pre-owned vehicles in
their inventory which are involved in a safety or compliance recall until the defect has been
remedied.
-END OF MESSAGE
***************************************************************************************************************
AUDI DEALER COMMUNICATION
Ensure all dealership personnel are aware of this notice so they are able to address customer questions. Contact Warranty if you require
additional assistance. Direct press inquiries to Audi Public Relations.
Audi Customer Protection 27i6_DLR_LAUNCH
Form No. F_3.4_AHQ-CP-C_029 Rev. 1.0
Repair Available – Safety Recall 27i6 / Terminal Cover
This notice is for: Dealer Principal
General Manager
Sales Managers
Service Manager
Parts Manager
Service Advisor
Warranty Administrator
Technicians
Date: January 11, 2021
Issue: The affected vehicles were erroneously equipped with a plus (positive) terminal cover
that might be less capable of assuring 12 V-power supply in a rear crash according to
FMVSS and CMVSS 301 (Fuel system integrity) at 80 km/h (approximately 50 mph). In
case of a rear crash (according to FMVSS/CMVSS 301 at 80 km/h (approximately 50
mph)) it may be possible for the 12-volt power supply of the vehicle to become
compromised.
While there is no noncompliance with FMVSS/CMVSS 301, this could result in not being
possible to open the vehicle doors from the outside, or the hazard warning lights may not
function due to a compromised electric power supply. This may lead to an increased risk
of injury to vehicle occupants in a rear crash if the power supply is affected.
Repair: REPAIR AVAILABLE – January 12, 2021 – Replace the plus (positive) terminal
cover.
See ELSA/ServiceNet for complete repair & claiming instructions
Check daily campaign open inventory report or OMD for affected vehicles in
inventory
Repair every affected inventory vehicle before delivery to consumers.
Parts Department: Dealers will be sent an initial allocation prior to customer notification. If no initial
allocation was received, please reference the Repair Projection Tool to view your
potential VIN population.
Affected Vehicles Country Beginning
Model Year
Ending
Model Year Vehicle Vehicle
Count
USA 2018 2019 RS5 COUPE 2,355
CAN 2018 2019 RS5 COUPE 447
*Counts reflect overall population; some vehicles may have already been repaired. Check Campaigns/Actions
screen in Elsa on the day of repair to verify that a VIN qualifies for repair under this action. Elsa is the only valid
campaign inquiry & verification source.
Notes: Schedule owner repairs immediately
Owner mailing – January 2021
IMPORTANT REMINDER: VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS
New Vehicles in Dealer Inventory: It is a violation of federal law for a dealer to deliver a new
motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by
this notification under a sale or lease until the defect or noncompliance is remedied. By law,
dealers must correct, prior to delivery for sale or lease, any vehicle that fails to comply with an
applicable Federal Motor Vehicle Safety Standard or that contains a defect relating to motor
vehicle safety.
Pre-Owned Vehicles in Dealer Inventory: Dealers should not deliver any pre-owned vehicles in
their inventory which are involved in a safety or compliance recall until the defect has been
remedied.
-END OF MESSAGE
***************************************************************************************************************
***************************************************************************************************************
SEOCONTENT-END
2 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| AUDI | RS5 | 2018-2019 |
10 Associated Documents
Remedy Instructions and TSB
RCRIT-20V760-3567.pdf 568.557KB
Manufacturer Notices(to Dealers,etc) – AUDI Date: December 17, 2020 Advance Notice – Safety Recall 27i6 / Terminal Cover
RCMN-20V760-6553.pdf 700.343KB
ISSUED Owner Notification Letter(Part 577) – 27i6 Audi Customer PRI
RCONL-20V760-3190.pdf 155.482KB
Recall Acknowledgement
RCAK-20V760-4160.pdf 243.972KB
Defect Notice 573 Report
RCLRPT-20V760-2755.PDF 216.126KB
ISSUED Owner Notification Letter(Part 577) – 27i6 Audi Customer
RCONL-20V760-0609.pdf 140.22KB
Recall Quarterly Report #1, 2021-1
RCLQRT-20V760-0458.PDF 211.158KB
Manufacturer Notices(to Dealers,etc) – Date: January 11, 2021 Repair Available – Safety Recall 27i6 / Terminal Cover
RCMN-20V760-1412.pdf 703.513KB
Recall Quarterly Report #2, 2021-2
RCLQRT-20V760-8292.PDF 211.26KB
Recall Quarterly Report #3, 2021-3
RCLQRT-20V760-3788.PDF 211.347KB
Latest Recalls Documents
- 【Powerful Battery Starter】The OXILAM car jump starter delivers a powerful peak current of 6000A, capable of quickly reviving a dead car battery in just seconds—even in extreme temperatures. A single full charge provides up to 60 jumpstarts. 2024 upgraded jumper cables can safely start all gas engines and 12L diesel engines, including 12v vehicles, motorcycles, pickups, RVs, tractors, trucks, vans, ATVs, snowmobiles, yachts, and many more. Say goodbye to being stranded due to a dead battery
- 【Multiple Security Protections】The OXILAM car battery jump starter features an integrated battery and intelligent clamps design, equipped with 10 intelligent safety protections to guard against short circuits, reverse polarity, sparks, and so forth. With enhanced thermal efficiency and power management, it ensures better performance and extends battery life, safeguarding the car battery starter from potential damage due to overheating, loose connections, battery bulging, and expansion
- 【Multifunctional Car Emergency Kit】This is an all-in-one car emergency kit that serves as a car jump starter, portable power bank and LED flashlight. It features 2 USB output ports (5V/3A, 9V/2A, 12V/1.5A), allowing for a 75% time saving when charging your mobile phone, tablet, Kindle, or digital camera. The device also boasts an upgraded Type-C input port(5V/3A, 9V/2A, 12V/1.5A)for faster charging. Additionally, it offers three 800-lumen LED light modes: flashlight, strobe, and SOS
- 【Sturdy and Considerate Design】This car jumper starter portable features a sturdy, waterproof shell and includes a protective cover to guard against wear and tear. The non-slip side design ensures a secure grip. Its ultra-compact and lightweight design allows for easy placement in your bag or car without taking up space. The battery jumper box is equipped with an LED screen that displays the battery status, providing an intuitive view of the battery's condition and remaining power
- 【Reliable Product Coverage】OXILAM battery jumper starter portable supply provides manufacturer protection and lifetime reliable Technical Support. Our 24-hour online after-sales team is ready to address any issues you may have. If you have any questions about the jump start battery pack get in touch with us for a satisfactory solution
- Powerful Jump Starter: Start your battery in seconds with our compact and powerful jump starter--with 5000A peak current car jump starter pack--up to 40 jump starts on a single charge and rated for gasoline engines up to 7 liters and diesel engines up to 5.5 liters. Safely start any 12-volt automotive car, truck, motorcycle, boat, RV or tractor ATVs, UTVs, lawnmowers, snowmobiles in a few minutes, even in extreme temperatures (-4°F~140°F).
- Portable Power Bank:Designed with 2 USB outputs (5V/3A)and (5V/2.4A), which can fully charge your cellphones, tablets, and other mobile devices at the fastest speed possible.We suggest to charge the jumper by 5V/2A adapter or above.
- Multi-Functional Booster:It's not only a car jump box, portable power bank, but also a LED flashlight.The battery starter utilizes bright LED flashlight with 3 modes (lighting/strobe/SOS/) under different circumstances. A car jumper comes in handy will help you find ways in an emergency or on an adventure trip.
- Safty Jump Starter:No worries about the misuse and sparks with built-in 8 types of protection such as spark-proof, reverse polarity protection, over-current protection, high-temperature protection, over-load protection etc. The car battery jump box indicator notifies you of incorrect use with an audible buzz and flashing lights.The hardened plastic and rubber corners make sure the starter safe.
- What you get: 1 X Biuble Portable Car Jump Starter,1 X Smart jumper cable,1 X USB Type-C Charging Cable,1 X Friendly User manual.Please contact with us for any problem and we provide 2-Year Technical Support and Warranty.
- 【8-IN-1 CAR BATTERY JUMP STARTER】This 12V Jump Box highlights highly integrated advanced functions but is more portable, transcending general battery booster. It's a portable car jump starter, tire pump, pressure gauge, portable power bank, flashlight, SOS signal, white strobe, red strobe as triangle warning light. Portable, versatile and must-have kit, your ultimate companion for emgencies, adventures and daily use!
- 【START COMPLETELY DEAD BATTERIES 】The jump starter power pack has 4500A and FORCE START FUNCTION as dual safeguard, can instantly start the most stranded vehicles including completely drained or low-voltag batteries even at -20℃~60℃. Durable jumper cables to reach varied battery terminals. Ideal for car, truck, motorcycle, lawnmower, boat, and more. Delivers multiple starts per charge, standby for about 24 months and support 1000+ recharge cycles.
- 【5+4+3 150PSI FAST AIR PUMP】Inflate your tires to 25 PSI in just a few minutes—faster and easier than ever! Powered by a 19-cylinder motor, the portable car jump starter delivers 150PSI high pressure and rapid air inflation. 5 inflation modes with auto memory and automatic shut-off to prevent over-inflation, 4 versatile nozzles, 3 selectable units (PSI, BAR, KPA), and a detachable extended hose for easy, space-saving storage.
- 【EMERGENCY 500LM LIGHTS & COMFORTABLE HANDLE】The jump starter power pack is featured with 500 lumens WIDE lights that is significantly brighter by more than 400%, providing 4-mode lights for different cases. SOS draws attention to a rescue when emergencies. White flashlight ensures vital visibility after dark, easy for read maps, make repairs, or inflate and change tires.White strobe can deter potential threats, red strobe doubles as warning triangle during roadside emergencies.
- 【TRUE CAPACITY & CHARGE ON THE GO】Always back you up even your phone is run out of power while no access to the charging station. Compatible with USB-C electronic devices, such as phones, tablets, cameras, etc. Delivers over 90% energy efficiency, keeping you informed of the real remaining battery level. 3.3" SMART DISPLAY keeps you updated on the jump box, clearly visible even in bright sunlight.
- Powerful and Durable - Powered by GOOLOO JUMPCORE technology, this 3000 amp portable car battery jumper starter provides instant restart for your 12V dead vehicles, supporting engines up to 9.0L for gas and 6.5L for diesel . Even if the battery voltage is extremely low, simply press the "BOOST" button to forcefully jump start your car. With over 1000+ charge cycles, this jump box for car battery is built to withstand extreme weather conditions ranging from -4°F to 140°F.
- Versatile and User-friendly - GOOLOO A3 portable car jump starter with air compressor offers 5 types of inflation modes (suv,car, bike ,ball and Customizable) and comes with 5 different nozzles, catering to the needs of both beginners and advanced users.Built in maximum pressure of 150 PSI and an air flow of 35L/Min. This tire pump can inflate Tesla Model 3/Y tire from 30 PSI to 36 PSI in just one minute! A full charge provides up to 45 minutes of wireless continuous inflation and supports unit switching 3 units (BAR/PSI/KPA).
- 7-in-1 Jump Starter – Built around GOOLOO TOOLCORE technology, the A3 is not only a portable car battery charger jump starter and a tire inflator, but also a built-in battery for emergency device charging, an LED flashlight, a bike pump, a ball pump, and a digital pressure gauge. Compatible with USB devices such as smartphones and tablets, it supports inflating 135 balls, 50 bicycle tires, 35 motorcycle tires, or 8 car tires with the included nozzles.
- All-Around Defense - Featuring GOOLOO SUPERSAFE technology and a high-efficiency battery management system (BMS), the A3 car jump box with air compressor offers 10 key protections, including short circuit protection, overcurrent protection, reverse connection protection, overheating protection, and overcharge protection.
- Smart cordless Tire Inflator - The A3 jump pack with tire inflator equipped with a smart LED screen, tire pressure detection and automatic shut-off functions make your operation more convenient. Ultra bright display stays perfectly readable in the harshest sunlight, no squinting or shielding required.
- 4000A&88.8Wh Jump Starter - Megavolt24 is equipped with a powerful 88.8Wh battery. this car battery jump starter is well-suited for 12V vehicles like cars, trucks, boats, and larger vehicles. wolfpack effectively restores your vehicle's power in emergency situations, supporting both gasoline and diesel engines with a capacity of under 10 liters
- HD LCD Display - The LCD screen offers a transparent presentation of all the status indicators for the car jump starter portable supply. Easily observe the current condition of your emergency power source, enabling smooth access to all functionalities.
- 65W USB-C Quick Charging - Featuring 1 * 65W Type-C in/out port, 1 * QC3.0 USB-A port, and coming with a PD65W fast charger, our jump start battery pack source can be fully charged in just 1.3 hours. Equipped with two output ports, it efficiently charges various electronic devices such as phones, laptops, and iPads, making it a perfect choice for travel or camping.
- One-Touch Booster and LED Flashlight - This jump starter features a one-touch boost function for starting vehicles under low voltage. It also includes an LED flashlight with SOS, strobe, and high-beam modes, serving as an essential emergency tool.
- Withstands -4 to 140°F & High Security - the portable battery jumper starter operates reliably in extreme conditions. It has passed various safety tests, including UL, FCC, CE, and CA65. With an IP64 protection rating, it ensures resilience in harsh environments.For safe operation, do not reverse clamp polarity. Always follow the instructions before use.
This product presentation was made with AAWP plugin.